| Current Path : /lib/dracut/modules.d/95fcoe/ |
Linux gator3171.hostgator.com 4.19.286-203.ELK.el7.x86_64 #1 SMP Wed Jun 14 04:33:55 CDT 2023 x86_64 |
| Current File : //lib/dracut/modules.d/95fcoe/module-setup.sh |
#!/bin/bash
# -*- mode: shell-script; indent-tabs-mode: nil; sh-basic-offset: 4; -*-
# ex: ts=8 sw=4 sts=4 et filetype=sh
check() {
local _fcoe_ctlr
[[ $hostonly ]] || [[ $mount_needs ]] && {
for c in /sys/bus/fcoe/devices/ctlr_* ; do
[ -L $c ] || continue
_fcoe_ctlr=$c
done
[ -z "$_fcoe_ctlr" ] && return 255
}
require_binaries dcbtool fipvlan lldpad ip readlink fcoemon fcoeadm || return 1
return 0
}
depends() {
echo network rootfs-block
return 0
}
installkernel() {
instmods fcoe 8021q edd
}
get_vlan_parent() {
local link=$1
[ -d $link ] || return
read iflink < $link/iflink
for if in /sys/class/net/* ; do
read idx < $if/ifindex
if [ $idx -eq $iflink ] ; then
echo ${if##*/}
fi
done
}
# called by dracut
cmdline() {
for c in /sys/bus/fcoe/devices/ctlr_* ; do
[ -L $c ] || continue
read enabled < $c/enabled
[ $enabled -eq 0 ] && continue
d=$(cd -P $c; echo $PWD)
i=${d%/*}
read mac < ${i}/address
s=$(dcbtool gc ${i##*/} dcb | sed -n 's/^DCB State:\t*\(.*\)/\1/p')
if [ -z "$s" ] ; then
p=$(get_vlan_parent ${i})
if [ "$p" ] ; then
s=$(dcbtool gc ${p} dcb | sed -n 's/^DCB State:\t*\(.*\)/\1/p')
fi
fi
if [ "$s" = "on" ] ; then
dcb="dcb"
else
dcb="nodcb"
fi
# Some Combined Network Adapters(CNAs) implement DCB in firmware.
# Do not run software-based DCB or LLDP on CNAs that implement DCB.
# If the network interface provides hardware DCB/DCBX capabilities,
# DCB_REQUIRED in "/etc/fcoe/cfg-xxx" is expected to set to "no".
#
# Force "nodcb" if there's any DCB_REQUIRED="no"(child or vlan parent).
grep -q "^[[:blank:]]*DCB_REQUIRED=\"no\"" /etc/fcoe/cfg-${i##*/} &>/dev/null
[ $? -eq 0 ] && dcb="nodcb"
if [ "$p" ] ; then
grep -q "^[[:blank:]]*DCB_REQUIRED=\"no\"" /etc/fcoe/cfg-${p} &>/dev/null
[ $? -eq 0 ] && dcb="nodcb"
fi
echo "fcoe=${mac}:${dcb}"
done
}
# called by dracut
install() {
inst_multiple ip dcbtool fipvlan lldpad readlink lldptool fcoemon fcoeadm
inst_libdir_file 'libhbalinux.so*'
[[ -e /etc/hba.conf ]] && inst "/etc/hba.conf" "/etc/hba.conf"
mkdir -m 0755 -p "$initdir/var/lib/lldpad"
mkdir -m 0755 -p "$initdir/etc/fcoe"
if [[ $hostonly_cmdline == "yes" ]] ; then
local _fcoeconf=$(cmdline)
[[ $_fcoeconf ]] && printf "%s\n" "$_fcoeconf" >> "${initdir}/etc/cmdline.d/95fcoe.conf"
fi
inst "$moddir/fcoe-up.sh" "/sbin/fcoe-up"
inst "$moddir/fcoe-edd.sh" "/sbin/fcoe-edd"
inst "$moddir/fcoe-genrules.sh" "/sbin/fcoe-genrules.sh"
inst_hook pre-trigger 03 "$moddir/lldpad.sh"
inst_hook cmdline 99 "$moddir/parse-fcoe.sh"
inst_hook cleanup 90 "$moddir/cleanup-fcoe.sh"
dracut_need_initqueue
}